The article deals with the processes of separation of thin films of oil liquids on the basis of rotary-belt type devices. The analysis of interaction of liquids and working body is made. The model of formation of oil films and their separation is described. the Studies create prerequisites for the development of engineering methods for calculating the design and operating parameters of the rotor-belt device for the formation of emulsion films and cleaning water surfaces from oil films, which is of great environmental importance.

Keywords: emulsion, film, apparatus, oil stain, viscosity, water surface cleaning

The process of cavitation is one of the reasons for the premature wear of pumping equipment components. Elements of a pumping wheel are subject to the greatest wear. In addition, cavitation causes undesirable effects such as vibration and noise. In order to reduce cavitational damage and increase the service life of pumping equipment, the authors of this article propose to install a special-shaped flow divider at the pump inlet that breaks the flow entering the pump into separate jets of a certain shape and structure.

Keywords: fluid, centrifugal pump, regulation, cavitation, flow, bubble, flow divider

The article deals with the work of mechanical absorbers, where the working body is presented in the form of a rotating cylinder. The analysis of interaction of liquids and a working body in similar devices is made. The mutual influence of liquid layers and the action of the working body are considered. The estimation of the force factors of the dynamic layer entrained by the rotating cylinder is obtained. The study presented in the article will help in the preparation of engineering methods for calculating the operating and design parameters of devices.

Keywords: absorber, emulsion layer, capillary forces, emulsion, static meniscus region, capillary pressure, immiscible liquids, rotating cylinder, liquid, Navier-Stokes equation

The article deals with the process of spraying immiscible liquid media with a disk spray. A mathematical model for determining the dispersion characteristics of spraying is proposed.

Keywords: liquid, atomization, flow, speed, dosing

The article discusses the process of sulfuric acid alkylation used to produce high-octane gasoline, as well as the design of jet reactors, their advantages and disadvantages. Based on the existing drawbacks of jet reactors, the development of a new high-efficiency jet reactor design has been proposed.

Keywords: reactor, sulfuric acid alkylation, isosurface, isocontours, gasoline, fractions, jet type, industry, oil refining

The article deals with the principle of emulsion formation in mechanical absorbers, where the working body is presented in the form of a rotating cylinder. The analysis of interaction of liquids in the process of emulsion formation is made. The mutual influence of liquid layers is considered. The estimation of internal and external parameters characterizing the process of emulsion formation is obtained. The study given in the article will help in the preparation of engineering methods for calculating the operating and design parameters of devices.

Keywords: absorber, emulsion layer, viscosity, density, emulsion, surface contact area, energy dissipation, immiscible liquids, rotating cylinder, liquid

The article deals with the issues of dispersion of heterogeneous liquids by spray nozzles in order to divide them into components. The influence of various parameters on the size of the droplets obtained is investigated. For the mathematical description the probabilistic approach is applied, which allows to obtain a differential function of the particle size distribution, which can form the basis of the engineering method of calculation of this class of separators. An expression for determining the average value of the angular velocity of the internal flow is compiled. These dependences allow us to calculate the most probable value of the angular velocity corresponding to the decay of complex drops into secondary ones, which are the drops of the initial liquids.

Keywords: particle, emulsion, non-uniform liquid, droplets, jet, nozzle, velocity, flow, parameter, separator

The article deals with the issues of dispersion of heterogeneous liquids by spray nozzles in order to divide them into components. The influence of various parameters on the size of the droplets obtained is investigated. For the mathematical description the probabilistic approach is applied, which allows to obtain a differential function of the particle size distribution, which can form the basis of the engineering method of calculation of this class of separators. An expression for determining the average value of the angular velocity of the internal flow is compiled. These dependences allow us to calculate the most probable value of the angular velocity corresponding to the decay of complex drops into secondary ones, which are the drops of the initial liquids.

Keywords: particle, emulsion, non-uniform liquid, droplets, jet, nozzle, velocity, flow, parameter, separator

The article deals with the issues of impact interaction of particles with layers of dispersed material of different thickness. The influence of the interaction velocity and the thickness of the substrate on the appearance and structure of the collision result is investigated. It is established that at low speeds there is a crater formation while the particle is on the substrate surface. With the growth of the interaction rate, the formation of a crown is observed, and particles penetrate into the substrate material. Experimentally determined the values of the velocity and thickness of the substrate, corresponding to the beginning of the formation of the crown.

Keywords: particle, blow, flow, splash, reflection, speed, stream, the bulk material flow, the recovery factor of speed, the substrate

Regulating the flow of liquids in pipe systems is carried out by different types of control valves. In the petroleum and chemical industries the most widely regulating valves straight-through type. However, in many constructions of valves of this type the problem of cavitation is not resolved completely. With the aim of reducing the negative impact of cavitation on the valve body and pipeline the authors have proposed and developed new designs of valves uniflow type organization of the fluid flow in internal cavities which helps to reduce cavitation effects.

Keywords: transportation, fluid valve, regulating, cavitation, flow, valves

the article presents an overview of the most common ways of measuring the volume (mass) of bulk materials currently used in various industries. The comparative analysis presented in the article methods of assessment. It is established that current methods of calculating volumes of granular media have a number of disadvantages, which significantly affects the quality of the product and its value. It is revealed that it is most expedient to carry out measurement of the volume of granular media directly in the containers or the vehicle taking into account the main characteristics of the material — moisture content, bulk and true density, temperature and fractional composition.

Keywords: bulk materials, volume, mass, rapid method, density weighing

Grinding particulate materials by means of impact is one of the most effective methods , especially when you want to obtain fine and superfine grinding . The most significant drawback - rapid and uneven wear on the blades and pneumatic organs. To solve this problem it was proposed to organize the interaction of shock . However, implementation of this method requires the establishment of methods for calculating the parameters of flow , as the incident on the bump , and ref"lected from it .

Keywords: crushing blow , collision, the diameter of the mill , the material particle , bump , flow , interaction, wear

Developed a rapid method for evaluation of the homogeneity of mixtures hardly separated granular materials, the analysis of which is the use of known methods is impossible or time-consuming. The method is based on the separation of mixture components by color using computer processing of pictures of her samples. To implement the developed computer program that can calculate the values of the coefficient of heterogeneity of the mixture, as well as other dispersion parameters.

Keywords: express method, the concentration of the mixture, component, granular material, image, distribution, shade of gray, the coefficient of heterogeneity

In this article shows the known constructions of gravitational continuous devices for mixing of bulk materials and the conditional classification of these devices. There is the problem of obtaining mixtures in cases when the volume-weighted amount of one component of the mixture is significantly greater than the second (with the ratio of their mass fractions of 1:10, and more). Typically, in the production for mixtures with a ratio 1:10 are used mixers centrifugal type, which operate in a periodic mode. The problem could be successfully solved using gravitational devices that operate in a continuous mode. The classification represented according to the design of mixers. The levels conventional classification for these mixers: (a) used or no additional mixing elements ; (b) the nature of their physical - mechanical properties.

Keywords: mixer, mixing, construction, mixture, component, bulk material, execution unit for mixing, tray, bunker, gravitation.

The analysis of existing methods of warming up the "old" asphalt with regard to its further use. Found that known methods of heat grinding are energy-intensive, which limits their use in industry. A new method of thermal regeneration based inkjet influence of coolant with subsequent classification of the particles.

Keywords: asphalt, grinding, heating, classification, agglomerate, device, analysis, method, jet, coolant, air